External brake
-
- G-Lieutenant Colonel
- Posts: 1089
- Joined: Wed Dec 23, 2009 6:21 pm
- Location: Fort Riley, KS
External brake
Alright, I've poured over all the pictures/diagrams I can find, to no avail. I'm trying to mount the External brake onto my GPW, and I can't seem to figure out how to get the drum on. I've got the linkage hooked up no problem, but I can't figure out how to mount the drum.
Does it mount on the rear dif or transfercase side of the output flange? If it mounts on the transfercase side, how do you keep the bolt heads from spinning while tightening it up?
Boone Myers
"My head hurts"
Does it mount on the rear dif or transfercase side of the output flange? If it mounts on the transfercase side, how do you keep the bolt heads from spinning while tightening it up?
Boone Myers
"My head hurts"
1-44 Ford GPW (161784) USA 20439314, USN 87559
5-4-45 Bantam T3 (68871) USA 0948627
5-4-45 Bantam T3 (68871) USA 0948627
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: External brake
It goes (the drum) on before the Companion Flange is installed, note that the bolt heads still have an edge to grab. Use fresh bolts with clean threads and put a bit of grease or oil on the threads for ease of installing/removing the nuts. If you do not have the original bolts, The Parts manuals call for A-6084 Bolts which have a smooth shoulder at the drum area and are 3/8" NF X 1-3/8" Long. Not sure if you can get by with 1-1/4" length, but 1-1/2" Long will work. Use GRADE 8 for this installation.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- artificer
- banned
- Posts: 13558
- Joined: Tue Jul 11, 2006 10:46 am
- Location: SINGAPORE
Re: External brake
Use locktite product which will "glue the bolts & head in place then let it set properly.Use fresh bolts with clean threads and put a bit of grease or oil on the threads for ease of installing/removing the nuts.
John GIBBINS Member Institute of Automotive Mechanical Engineers [Ret], ASE Master Medium/Heavy Truck & Auto Technician USA -2002 Licensed Motor Mech NSW MVIC 49593 Current 2015
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
- Jon
- Australian Army (Retired) R.A.E.M.E.
- Posts: 11949
- Joined: Mon May 04, 1998 8:00 pm
- Location: Down Under In Queensland
- Contact:
Re: External brake
Did I miss anything ?
Jon Rogers
AUSTRALIA
http://jeepdraw.com JeepDraw Home Page & Drawings
Parts Colours Page http://jeepdraw.com/PART_COLOURS.htm
1944 GPW195611 20531384 ACM-2 17781
1942 MBT 19433W
AUSTRALIA
http://jeepdraw.com JeepDraw Home Page & Drawings
Parts Colours Page http://jeepdraw.com/PART_COLOURS.htm
1944 GPW195611 20531384 ACM-2 17781
1942 MBT 19433W
-
- G-Lieutenant Colonel
- Posts: 1089
- Joined: Wed Dec 23, 2009 6:21 pm
- Location: Fort Riley, KS
Re: External brake
Perfect, thanks for all the tips/pictures!
Thanks!
Boone Myers
Thanks!
Boone Myers
1-44 Ford GPW (161784) USA 20439314, USN 87559
5-4-45 Bantam T3 (68871) USA 0948627
5-4-45 Bantam T3 (68871) USA 0948627
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: External brake
[quote="artificer"][quote]Use fresh bolts with clean threads and put a bit of grease or oil on the threads for ease of installing/removing the nuts.[/quote] Use locktite product which will "glue the bolts & head in place then let it set properly.[/quote]
John, this will not work, there is no glue in the world that will hold these bolts in place.
John, this will not work, there is no glue in the world that will hold these bolts in place.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
-
- G-Command Sergeant Major
- Posts: 239
- Joined: Wed Jul 15, 2009 3:27 pm
- Location:
Re: External brake
I just did this sunday, the drum needs to be clear inside as possible, insert the flange into position as shown in the pics, then put the bolts in from the inside of the drum, you will see how the lip of the flange inside the drum will catch the edge of the bolt head to keep it from spinning as you tighten the nuts. you then slide the flange on to the splines, holding the bolts in place in place with your fingers, when it is all the way in the bolts will woble around but should not fall out, then you put on the ujoint assembly , if you have thin fingers you can push the bolts out so you can nut them.
-
- Sergeant Major of the Gee
- Posts: 372
- Joined: Mon Apr 19, 2010 4:06 am
- Location: Lugoff, SC
Re: External brake
From what you all are describing, mine sounds different. I put my drum back on the transfercase this weekend as well, but it appeared to have studs in the drum, not bolts. They were certainly not loose at all. We are talking about the four bolts/studs that the rear u joint flange mounts to, correct? Mine seem to be pressed in, almost like wheel lugs and have round heads. It is the drum for the external contracting bang type brake and was pretty original looking to the f script transefercase it came off of. Do I have something different?
-Dan
1945 GPW 267188 (numbers matching)
1945 GPW 267188 (numbers matching)
- artificer
- banned
- Posts: 13558
- Joined: Tue Jul 11, 2006 10:46 am
- Location: SINGAPORE
Re: External brake
Not everyone uses ex GI 1940's & 50's era gasket cement & shelac.Joel incorrectly said: John, this will not work, there is no glue in the world that will hold these bolts in place.
Time to get with the times & try something new old fella. I've done this dozens of times & it works for moi.
Possibly original? or after market, I have only seen hex head.Dan said: They were certainly not loose at all. We are talking about the four bolts/studs that the rear u joint flange mounts to, correct? Mine seem to be pressed in, almost like wheel lugs and have round heads.
The drum is on the inside of the flange & closest to the t/f case housing.
As Hatchetdan described it can be done but it can be painful.
Here is how to go:
The flange is off the vehicle RIGHT?
Fit the drum to the inside of the flange then fit the bolts using the locking material you choose http://au.iloctite.com/upload/media/media/18/P_20_21" onclick="window.open(this.href);return false;[488].pdf
....even super glue will work fine, use acetone or nail polish remover to clean....
With a couple of washers on each bolt (to cover the smooth bolt shank), ensure adhesive is not on threads or the outside of the flange @ all, then tighten the nuts on all 4 of the bolts & let the adhesive set..
Fit the flange/drum to the transfer case output shaft spline using the appropriate sealant on the internal & external splines & using grease on the seal plus its mating surface on the flange.
Ensure there is @ least 1/8"or 3mm tighten up space (crush) between the end of the transmission output spline & where the washer will sit in the flange under the nut after the flange is pushed right home.
Then fill this void space with silicon, fit the smooth washer & torque the nut to 220#lb. Clean off squashed out compound.
There are some "new" bad flanges which are too short & will not exhibit this necessary 'crush" aspect. DON'T USE THEM.
A few hours later or next day remove these 4 nuts & washers, fit up the drive shaft carefully & refit the 4 nuts this time with spring washers to 35#lb then connect the other drive shaft end to the differential.
John GIBBINS Member Institute of Automotive Mechanical Engineers [Ret], ASE Master Medium/Heavy Truck & Auto Technician USA -2002 Licensed Motor Mech NSW MVIC 49593 Current 2015
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: External brake
There is sufficient room to hold the head of each bolt against the inside edge of theCompanion Flange with the finger tips, there is sufficent shoulder on the Companion Flange where it enters thru the Parking Brake Drum to catch the flats of the bolts and prevent them from turning. (It was designed this way). If the bolts threads are clean and oiled, this is all that is necessary for easy installation and removal. There is no need to glue the bolts in place and wait overnight. The installation and tightening of the propeller Shaft to this flange is about a 20 minute job if all goes well. Jeep mechanics have been doing this simple procedure for 70 years with ease. There are times when the bolt threads are rusty or dirty, and the bolt heads may want to slide in a bit, a 9/16" Open End wrench can just fit in enough to assist in holding the stubborn bolts.
The original A-6084 Bolts have a fitting shoulder apprximately 13/16" long and are a snug fit where they pass thru the drum and flange, regular bolts may fit looser, but glue is not necessary. I always kept a supply of NOS A-6084 Bolts on hand for this very task on MB thru CJ Jeeps.
The original A-6084 Bolts have a fitting shoulder apprximately 13/16" long and are a snug fit where they pass thru the drum and flange, regular bolts may fit looser, but glue is not necessary. I always kept a supply of NOS A-6084 Bolts on hand for this very task on MB thru CJ Jeeps.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
- artificer
- banned
- Posts: 13558
- Joined: Tue Jul 11, 2006 10:46 am
- Location: SINGAPORE
Re: External brake
hatchetdan & the only "real" jeep mechanic still around have both told us the hard way to do things [it will work]....I have suggested the easy way from my experience, given detailed explanation & hope that has been helpful to some.To arrive at the simplest truth requires years of contemplation [which is not taught @ jeep mechanic academy.]" Isaac Newton
"I am looking for people who have an infinite capacity to not know what can’t be done." Henry Ford.
John GIBBINS Member Institute of Automotive Mechanical Engineers [Ret], ASE Master Medium/Heavy Truck & Auto Technician USA -2002 Licensed Motor Mech NSW MVIC 49593 Current 2015
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
TO DIAGNOSE, TROUBLESHOOT OR FAULT FIND ANY AUTO SYSTEM....
Understand how system parts interact with one another. GOOD parts can then be established & the NOT GOOD problem/s part/s isolated for repair or replacement.
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: External brake
And Boone, let me know if you need the A-6084 Bolts for the Companion Flange,I will send you 4 NOS..
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
-
- G-Lieutenant Colonel
- Posts: 1089
- Joined: Wed Dec 23, 2009 6:21 pm
- Location: Fort Riley, KS
Re: External brake
Alright, well after toying with it for an hour or so I finally got it mounted. The bolts were originals, and the lip on the flange held all the bolts from turning except one. I disconected the driveshaft from the rear diff and was able to turn the brake drum so I could get a wrench through to hold the bolt head while I tightend the nut. Everything seems to work fine, so now I just need to get an e-brake cable and hook it up to my brake handle. Thanks again for the tips, I'll have to post some pictures later.
Boone Myers
Boone Myers
1-44 Ford GPW (161784) USA 20439314, USN 87559
5-4-45 Bantam T3 (68871) USA 0948627
5-4-45 Bantam T3 (68871) USA 0948627
-
- Sergeant Major of the Gee
- Posts: 372
- Joined: Mon Apr 19, 2010 4:06 am
- Location: Lugoff, SC
Re: External brake
After second thought, I may be wrong. I was just going from memory, and I think maybe they were just fused together after all these years. I know that the flange (the part that has the splines and mounts on the transfer case rear output shaft) was firmly attached to the drum as well as the four bolts. The F marked case I rebuilt came from AZ and was very rusty, so I blasted all the parts and had the drum turned at the NAPA in town to make sure it was true. Perhaps someone else already had the super glue idea Anyway, glad you got yours mounted and working Myers!
-Dan
1945 GPW 267188 (numbers matching)
1945 GPW 267188 (numbers matching)
Who is online
Users browsing this forum: No registered users and 113 guests