gpw timing chain cover
-
- G-Major General
- Posts: 3092
- Joined: Wed Dec 25, 2002 6:58 pm
- Location: Lafayette, Colorado
gpw timing chain cover
Looking for a goodnight timing chain over for my 45gpw. Need to have a good oil squirt piece attached.
Lew Ladwig
CMHG, 9th ID, Commander
BSA Crew 42 Advisor, 9th ID reenactors
CFFC, IFFC president
2-'47 cj2a's
1-'45 gpw in full resto mode
CMHG, 9th ID, Commander
BSA Crew 42 Advisor, 9th ID reenactors
CFFC, IFFC president
2-'47 cj2a's
1-'45 gpw in full resto mode
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: gpw timing chain cover
The Oil Jet is screwed into the face of the block and is aimed at the junction of the Camshaft and Timing Gear. only thing on the cover is the factory sweated on fitting for the oil return line and the riveted on peg that controls camshaft end play on the Chain type engine only.
The Gear type engines have a cover that is plain inside. If your oil pressure gage is a repro, I would suspect it as they have a history of antics.
NOTE:
Repro is not to be confused with long established aftermarkets.
The Gear type engines have a cover that is plain inside. If your oil pressure gage is a repro, I would suspect it as they have a history of antics.
NOTE:
Repro is not to be confused with long established aftermarkets.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
-
- G-Major General
- Posts: 3092
- Joined: Wed Dec 25, 2002 6:58 pm
- Location: Lafayette, Colorado
Re: gpw timing chain cover
Ben,
I checked the oil hole and it looks ok. I will check the mains next weekend and blow air though the system. I will check the spring on the oil pump and see if it seems to work. Not sure how to ensure the pump valve does not stick open.
I checked the oil hole and it looks ok. I will check the mains next weekend and blow air though the system. I will check the spring on the oil pump and see if it seems to work. Not sure how to ensure the pump valve does not stick open.
Lew Ladwig
CMHG, 9th ID, Commander
BSA Crew 42 Advisor, 9th ID reenactors
CFFC, IFFC president
2-'47 cj2a's
1-'45 gpw in full resto mode
CMHG, 9th ID, Commander
BSA Crew 42 Advisor, 9th ID reenactors
CFFC, IFFC president
2-'47 cj2a's
1-'45 gpw in full resto mode
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: gpw timing chain cover
If you do remove the oil pan, start with the rod bearings first. With the pan off see if you can move the cam shaft fore and aft.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
Who is online
Users browsing this forum: No registered users and 44 guests