GPW exhaust pipe bond strap or dimensions
-
- G-Lieutenant General
- Posts: 3598
- Joined: Fri Dec 13, 2002 2:54 pm
- Location: Sydney, Australia.
- Contact:
GPW exhaust pipe bond strap or dimensions
Hi all,
Does anyone have one of the bond straps which attaches to the exhaust pipe (and i think back to the engine)? I have a kit from Ron, however it is no longer included in the kit he sells (as at november 09). I can supply a pic if that helps anyone to identify what i am after.
NOS, repro or used in good condition, i`ll take anything! Alternatively, can anyone give dimensions so i can make one? I have the braided strap so can easily make it if i knew sizes etc.
Thanks,
Ian.
Does anyone have one of the bond straps which attaches to the exhaust pipe (and i think back to the engine)? I have a kit from Ron, however it is no longer included in the kit he sells (as at november 09). I can supply a pic if that helps anyone to identify what i am after.
NOS, repro or used in good condition, i`ll take anything! Alternatively, can anyone give dimensions so i can make one? I have the braided strap so can easily make it if i knew sizes etc.
Thanks,
Ian.
Australian Jeep Investigator
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: GPW exhaust pipe bond strap or dimensions
Let me check my header pipe when I get home. Shoot me a PM to remind me. I cannot remember if the bond strap is intact. If it's NOT, I'll check the repro strap on Bob Shaw's jeep and get you those dimentions. If you end up making them, I'll take one if you didn't mind.
How goes the hardware order?
How goes the hardware order?
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
-
- G-First Lieutenant
- Posts: 616
- Joined: Fri Jul 02, 2004 5:58 pm
- Location: Victoria Australia
Re: GPW exhaust pipe bond strap or dimensions
G'day Ian,
First up mate merry xmas to you and your partner I hope you both that a good one.
Back to business, have you that a looking in AAW vol one on page 97! it give you some of the dimentions that may help you.
cheers for now
Ian
First up mate merry xmas to you and your partner I hope you both that a good one.
Back to business, have you that a looking in AAW vol one on page 97! it give you some of the dimentions that may help you.
cheers for now
Ian
MB 311192 ARN 157967
Gpw 161919
Aus Trailer No3a, 43
Aus Trailer No4, 45
41 Fordson WOT2-H
G506 Chevy
Gpw 161919
Aus Trailer No3a, 43
Aus Trailer No4, 45
41 Fordson WOT2-H
G506 Chevy
-
- G-Lieutenant General
- Posts: 3598
- Joined: Fri Dec 13, 2002 2:54 pm
- Location: Sydney, Australia.
- Contact:
Re: GPW exhaust pipe bond strap or dimensions
Hi guys,
Luke- i shall check AAW as Ian has said. If all else fails, i shall get back to you for details from yours/bobs. If i make one (which i likely will), i`ll make a few- one with your name on for sure. As for the hardware order, it has slowed down abit- christmas pulled me up on time! I shall get back into it after new years if thats ok?
Ian- Merry christmas and new years to you and the family too! It has been great so far- i ate alot, but dont feel like an elephant... so i shall keep on eating!
Thanks for the tip on AAW- i had forgotten about the bond strap info in there! I really should make a point of looking through the manuals on a more regular occurance- everytime i do, i find remember or even something new that i had missed on the previous read!
Cheers all,
Ian.
Luke- i shall check AAW as Ian has said. If all else fails, i shall get back to you for details from yours/bobs. If i make one (which i likely will), i`ll make a few- one with your name on for sure. As for the hardware order, it has slowed down abit- christmas pulled me up on time! I shall get back into it after new years if thats ok?
Ian- Merry christmas and new years to you and the family too! It has been great so far- i ate alot, but dont feel like an elephant... so i shall keep on eating!
Thanks for the tip on AAW- i had forgotten about the bond strap info in there! I really should make a point of looking through the manuals on a more regular occurance- everytime i do, i find remember or even something new that i had missed on the previous read!
Cheers all,
Ian.
Australian Jeep Investigator
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
- USAFpj
- G-Brigadier General
- Posts: 2217
- Joined: Sun Aug 08, 2004 1:02 pm
- Location: SC
Re: GPW exhaust pipe bond strap or dimensions
Ian, did you get your dimensions? I am away from home, but do have one that I removed from a slat header pipe. I can get the dimensions to you tomorrow night if need be. The strap is intact as well.
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: GPW exhaust pipe bond strap or dimensions
Ian, take your time. The jack is still yours and will be here until you are ready for it. Just remember, yours is the one WITHOUT the stampings on the base.
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
-
- G-Lieutenant General
- Posts: 3598
- Joined: Fri Dec 13, 2002 2:54 pm
- Location: Sydney, Australia.
- Contact:
Re: GPW exhaust pipe bond strap or dimensions
Hi USAFpj and Luke,
I have the dimensions out of AAW1 as Ian suggested. There are just a few dimensions i would like if possible to get from you as they arent as clear (or to me?) in AAW.
In AAW, it shows a rectangular piece which i assume wraps around the woven strap and the piece of iron which attaches to the header/exhaust pipe- can you tell me how big this is?
Also, what is the distance of the flat pice of iron between this wrap around strap and the beginning of the bend to go aroundthe header/exhaust pipe?
I dont suppose you could also comment on how it was attached to the pipe? Is it welded or soldered or brazed?
Luke- thanks mate! Will be in contact soon.
Thankyou,
Ian.
(I also had a pic of a ford marked one i saved from ebay, but i can no longer find it which is a bummer!)
I have the dimensions out of AAW1 as Ian suggested. There are just a few dimensions i would like if possible to get from you as they arent as clear (or to me?) in AAW.
In AAW, it shows a rectangular piece which i assume wraps around the woven strap and the piece of iron which attaches to the header/exhaust pipe- can you tell me how big this is?
Also, what is the distance of the flat pice of iron between this wrap around strap and the beginning of the bend to go aroundthe header/exhaust pipe?
I dont suppose you could also comment on how it was attached to the pipe? Is it welded or soldered or brazed?
Luke- thanks mate! Will be in contact soon.
Thankyou,
Ian.
(I also had a pic of a ford marked one i saved from ebay, but i can no longer find it which is a bummer!)
Australian Jeep Investigator
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
- USAFpj
- G-Brigadier General
- Posts: 2217
- Joined: Sun Aug 08, 2004 1:02 pm
- Location: SC
Re: GPW exhaust pipe bond strap or dimensions
I will get the dimensions and post shortly...
- USAFpj
- G-Brigadier General
- Posts: 2217
- Joined: Sun Aug 08, 2004 1:02 pm
- Location: SC
Re: GPW exhaust pipe bond strap or dimensions
Ian, the rectangular fold is 3/4ths inches in length, and is located 7/8ths inch from the bend. The wrapped piece comes close, but does not completely wrap around the entire flat portion of the iron. The bent portion is spot welded once on one side, and a one inch weld bead on the other. Any other measurements? If you need this as a model, PM me and I'll send it to you for a small trade.
-
- G-Lieutenant General
- Posts: 3598
- Joined: Fri Dec 13, 2002 2:54 pm
- Location: Sydney, Australia.
- Contact:
Re: GPW exhaust pipe bond strap or dimensions
Thankyou very much! Those will help immensely.
Thanks also for the generosity to send it along too, however i shall pass. I am happy to go off the pics you posted and AAW to try and make it. I dont necessarily need it, so i wont be greedy!
As a side note, i thought i would add this post in from Bill M with info about placement and connection for future reference.
http://www.g503.com/forums/viewtopic.ph ... ap#p787430" onclick="window.open(this.href);return false;
Cheers and thanks one and all!
Ian.
Thanks also for the generosity to send it along too, however i shall pass. I am happy to go off the pics you posted and AAW to try and make it. I dont necessarily need it, so i wont be greedy!
As a side note, i thought i would add this post in from Bill M with info about placement and connection for future reference.
http://www.g503.com/forums/viewtopic.ph ... ap#p787430" onclick="window.open(this.href);return false;
Cheers and thanks one and all!
Ian.
Australian Jeep Investigator
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
MB: 131175
GPW: 11730.
GPW: 225290.
Aust trailer: GMH 3- #211
http://www.vintageengines.net
- Jon
- Australian Army (Retired) R.A.E.M.E.
- Posts: 11949
- Joined: Mon May 04, 1998 8:00 pm
- Location: Down Under In Queensland
- Contact:
Re: GPW exhaust pipe bond strap or dimensions
Ian,
I found this in my files...... it may help
JR
I found this in my files...... it may help
JR
- Attachments
-
- exhaust-ground.jpg (38.83 KiB) Viewed 3185 times
Jon Rogers
AUSTRALIA
http://jeepdraw.com JeepDraw Home Page & Drawings
Parts Colours Page http://jeepdraw.com/PART_COLOURS.htm
1944 GPW195611 20531384 ACM-2 17781
1942 MBT 19433W
AUSTRALIA
http://jeepdraw.com JeepDraw Home Page & Drawings
Parts Colours Page http://jeepdraw.com/PART_COLOURS.htm
1944 GPW195611 20531384 ACM-2 17781
1942 MBT 19433W
- wjohn
- LTCOL, RA Sigs
- Posts: 8012
- Joined: Mon Apr 07, 2008 10:23 pm
- Location: Country Victoria, Australia
Re: GPW exhaust pipe bond strap or dimensions
Does any one have photos of the Strap attached to the pipe.
The photo I have (i'll scan later today) shows the strap attached to the pipe, Welded on, on the outboard side of the pipe.
It would great to get a dimension of how far down the pipe the strap is attached, what the welds look like, and orientation.
Thanks in advance.
Pics added
The photo I have (i'll scan later today) shows the strap attached to the pipe, Welded on, on the outboard side of the pipe.
It would great to get a dimension of how far down the pipe the strap is attached, what the welds look like, and orientation.
Thanks in advance.
Pics added
GPW 204556
USA 20536862
MB371922
ACM2 Tub 23298
MB130849
ARN: 79731
DOD 26 Mar 1942
USA 20536862
MB371922
ACM2 Tub 23298
MB130849
ARN: 79731
DOD 26 Mar 1942
- wjohn
- LTCOL, RA Sigs
- Posts: 8012
- Joined: Mon Apr 07, 2008 10:23 pm
- Location: Country Victoria, Australia
Re: GPW exhaust pipe bond strap or dimensions
Pics Added.
GPW 204556
USA 20536862
MB371922
ACM2 Tub 23298
MB130849
ARN: 79731
DOD 26 Mar 1942
USA 20536862
MB371922
ACM2 Tub 23298
MB130849
ARN: 79731
DOD 26 Mar 1942
-
- MechTech
- Posts: 3961
- Joined: Sat Dec 14, 2002 12:07 am
- Location: The Workshop
Re: GPW exhaust pipe bond strap or dimensions
John,
this photo is an enlargement from the well known batch of June 1942 WO factory images from the Life archive.
The GPW photographic equivalent still eludes me
cheers
Bill.
[attachment=0]1942 Willys MB factory inpection pit photo exhaust header pipe bond strap.jpeg[/attachment
this photo is an enlargement from the well known batch of June 1942 WO factory images from the Life archive.
The GPW photographic equivalent still eludes me
cheers
Bill.
[attachment=0]1942 Willys MB factory inpection pit photo exhaust header pipe bond strap.jpeg[/attachment
- Attachments
-
- 1942 Willys MB factory inpection pit photo exhaust header pipe bond strap.jpeg (163.27 KiB) Viewed 2899 times
Member of G503 since 1999
GPW-178721 Under restoration.
GPW-178721 Under restoration.
- Old Pal
- G-Major
- Posts: 863
- Joined: Sun May 04, 2014 4:39 pm
- Location: Kelseyville, CA, USA
Re: GPW exhaust pipe bond strap or dimensions
Any update on this?wjohn wrote:Does any one have photos of the Strap attached to the pipe.
The photo I have (i'll scan later today) shows the strap attached to the pipe, Welded on, on the outboard side of the pipe.
It would great to get a dimension of how far down the pipe the strap is attached, what the welds look like, and orientation.
Thanks in advance
Who is online
Users browsing this forum: No registered users and 39 guests