Stove cooker bolt hole..
Moderator: Kurt Lesser
-
- G-Lieutenant Colonel
- Posts: 1142
- Joined: Sat Dec 18, 2004 4:40 am
- Location: Lansing, michigan
- Contact:
Stove cooker bolt hole..
Anyone know the thread pitch on the 2 fittings im pointing to in the pic.. I have always see it say gas cooker goes there..
I have the brackets and the strap for it but no clue on the threads
thanks in advance
Joel
I have the brackets and the strap for it but no clue on the threads
thanks in advance
Joel
Joel
1987 2 door M998
2001 M1102
1987 2 door M998
2001 M1102
- Kurt Lesser
- G-Lieutenant General
- Posts: 3779
- Joined: Sun May 16, 2004 3:08 pm
- Location: San Jose, Ca
- Contact:
-
- G-Lieutenant Colonel
- Posts: 1142
- Joined: Sat Dec 18, 2004 4:40 am
- Location: Lansing, michigan
- Contact:
- dunsbr
- G-Lieutenant General
- Posts: 4098
- Joined: Thu Dec 09, 2004 2:53 pm
- Location: Melbourne, Australia
- Contact:
-
- G-Lieutenant Colonel
- Posts: 1142
- Joined: Sat Dec 18, 2004 4:40 am
- Location: Lansing, michigan
- Contact:
- dunsbr
- G-Lieutenant General
- Posts: 4098
- Joined: Thu Dec 09, 2004 2:53 pm
- Location: Melbourne, Australia
- Contact:
I bet that's what you say to all the girls!hummer4x4guy wrote:how bout a length?
If I were you, I'd use what ever I had lying around in mybolt box!
It'd only need to be around 1/2" to do the job OK, but being longer wouldn't be a problem.
Cheers
Brad Dunstan
RHD '87 M1026
(with 4L80E Trans, 242 T/case, 12K hubs, CTIS, A2 wiring, Air Con, A2 ebrake, 9k Winch,
Serpentine Belt Accessory Drive & Eaton e-lockers)
RHD '87 M1026
(with 4L80E Trans, 242 T/case, 12K hubs, CTIS, A2 wiring, Air Con, A2 ebrake, 9k Winch,
Serpentine Belt Accessory Drive & Eaton e-lockers)
- dunsbr
- G-Lieutenant General
- Posts: 4098
- Joined: Thu Dec 09, 2004 2:53 pm
- Location: Melbourne, Australia
- Contact:
-
- G-Lieutenant Colonel
- Posts: 1142
- Joined: Sat Dec 18, 2004 4:40 am
- Location: Lansing, michigan
- Contact:
*clears throat*
hummm... if a 1/2 will do it..I wonder if I can sell my extraness to some poor sap who needs a bit of a boost?
I guess yer right 1/2 will work since there isnt even anything going in there right now...
I did just get the rubberduck hood lift installed... I have to SLOW DOWN the hood on open its soo freaking great!!!
Now I just have to tighten down the bolts and hook up lines fill coolant and get more tranny fluid since it spilled out when i pulled my tube and dipstick outa it
Should be up and running in several few more hours
hummm... if a 1/2 will do it..I wonder if I can sell my extraness to some poor sap who needs a bit of a boost?
I guess yer right 1/2 will work since there isnt even anything going in there right now...
I did just get the rubberduck hood lift installed... I have to SLOW DOWN the hood on open its soo freaking great!!!
Now I just have to tighten down the bolts and hook up lines fill coolant and get more tranny fluid since it spilled out when i pulled my tube and dipstick outa it
Should be up and running in several few more hours
Joel
1987 2 door M998
2001 M1102
1987 2 door M998
2001 M1102
Who is online
Users browsing this forum: No registered users and 50 guests