Resizing cases for 37mm Gun, Antitank, M3A1 US
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
Resizing cases for 37mm Gun, Antitank, M3A1 US
Resizing cases for 37mm Gun, Antitank, M3A1 US
Sizing cases. Large stack of stuff, see pic. I am full length resizing because that is the die set I have. A lot of them probably need it anyway because they were really swollen. Some were not too bad but none would chamber in my gun. The first one took me years to complete, finding and buying equipment and figuring out how to use it. The next one took me a couple of hours, stuck cases, adjustments on the press, finding more spacers etc. I am down to 15 to 21 minutes now after about 10 cases done.
Sizing cases. Large stack of stuff, see pic. I am full length resizing because that is the die set I have. A lot of them probably need it anyway because they were really swollen. Some were not too bad but none would chamber in my gun. The first one took me years to complete, finding and buying equipment and figuring out how to use it. The next one took me a couple of hours, stuck cases, adjustments on the press, finding more spacers etc. I am down to 15 to 21 minutes now after about 10 cases done.
- Attachments
-
- finished resizing small.jpg (192.81 KiB) Viewed 1277 times
-
- Start of sizing small.jpg (202.05 KiB) Viewed 1277 times
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
Test fired my reloads. Three worked fine. The other 3 would not chamber because when I had pressed in the projectiles they were slightly off, so that left a .023 bump in case on one side in neck area, so they would not chamber.
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
-
- G-Captain
- Posts: 733
- Joined: Tue Dec 14, 2004 5:18 pm
- Location: Suppository USA (aka Kalifornia)
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
What lubricant, did you end up using, for resizing the cases ?
*
MVCC member since 1983
MVCC Life member since around 1985
MVPA member since 1983
MVPA life member since around 1985
MVCC member since 1983
MVCC Life member since around 1985
MVPA member since 1983
MVPA life member since around 1985
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
The reccomendation from the die set was to use "MasterPro Hi Temp Disc Wheel Bearing Grease" but I could not find it so I bought the stuff in the pic from Walmart. It was red and high temp so it looked the same, but the die set said any wheel bearing grease would work. Do not use small arms case lube or the dies will stick. The process was:Kim Sievert wrote:What lubricant, did you end up using, for resizing the cases ?
1. Clean with Scotch Brite Maroon Pads for metal I bought at Menards.
2.Wipe it clean so you can feel no grit.
3.Grease the case with the wheel bearing grease, then wipe gently with a rag until the case feels greasy but you can not see the red grease. Just needs a thin layer.
3.Then I pressed on my die set one peice at a time with a $120 Harbor Freight 12ton Hydraulic press. Sometimes when the case was espcially swollen I would regrease the middle third again, after the first die was pressed to the bottom of the case. The first die would seem to wipe the case dry and I would get a lot of chatter(sudder?) when I pressed on the second die.
4.I have not gotton any cases stuck yet, knock on wood.
- Attachments
-
- Grease I used from Walmart
- axle grease small.jpg (157.09 KiB) Viewed 1142 times
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
-
- G-First Lieutenant
- Posts: 640
- Joined: Thu Dec 30, 2004 6:45 pm
- Location:
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
Hi,
Where did you get your resizing dies from?
Thanks,
Dave
Where did you get your resizing dies from?
Thanks,
Dave
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
Ira sellers, he had a post on this board and was selling die sets.
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
easy cheap hack to final size neck after projo set
I was having problems with fit in my 37mm with some of my unfired cases after I pressed in the projo. I used a $8 pipe clamp from amazon to squeeze the neck back down to size. Now my cases fit perfect and slide right in with out hanging up. Cheap hack see pic.
- Attachments
-
- projo hack 38.JPG (52.25 KiB) Viewed 890 times
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
Pulling projos
Tried to pull some projectiles by using the inertia method with a piece of pipe, almost worked but would not come out all the way, also beat up the concrete on my garage floor. So made a slide hammer type puller with a part from my die set and a $8 pipe clamp from amazon. Worked but still had to do a lot of banging on the case, see pic. Anybody out there got any other ideas?
- Attachments
-
- projo puller (2).JPG (50.07 KiB) Viewed 871 times
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
-
- G-Major General
- Posts: 2591
- Joined: Wed Sep 19, 2007 11:14 am
- Location: denver co.
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
I thing the guy in california uses Pam cooking spray for lube. but it seems like everyone has a different set of dies.
but all you guys need to go easier on the brass.
BB
but all you guys need to go easier on the brass.
BB
keeping it strac here boss
I hate aquaphobic horses
I hate aquaphobic horses
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
Source for pipe clamps on Amazon
Climax Part 2C-150, Mild Steel, Black Oxide Plating, Clamping Collar, 1 1/2 inch bore, 2 3/8 inch OD, 9/16 inch Width, 1/4-28 x 3/4" Clamp Screw
Link here, they come in different sizes
https://www.amazon.com/gp/product/B0020 ... UTF8&psc=1
Climax Part 2C-150, Mild Steel, Black Oxide Plating, Clamping Collar, 1 1/2 inch bore, 2 3/8 inch OD, 9/16 inch Width, 1/4-28 x 3/4" Clamp Screw
Link here, they come in different sizes
https://www.amazon.com/gp/product/B0020 ... UTF8&psc=1
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
-
- G-Colonel
- Posts: 1420
- Joined: Mon Jan 06, 2003 4:47 pm
- Location: St Louis, Missouri
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
we have a full length case die...Use very light coat of Mobil 1 synthetic.....works great.
M3 37mm Cannon Parts and Resin Weapon Replicas. We also manufacture reproduction Stuart parts.
Fuel tanks, Rear Exhaust and Air Deflectors, and other components.
314-703-9710
Fuel tanks, Rear Exhaust and Air Deflectors, and other components.
314-703-9710
- waterdawg2004
- Sergeant Major of the Gee
- Posts: 287
- Joined: Tue Jul 20, 2010 4:11 am
- Location: Wy & SD
Re: Resizing cases for 37mm Gun, Antitank, M3A1 US
Nice, do you have a pic and price?
1944 MB Jeep
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
37mm Gun, Antitank, M3A1 USA
French 25mm SA.L Model 1937
Replica Kubelwagen from VW Thing
Who is online
Users browsing this forum: No registered users and 38 guests