chain vs gear driven block
- Fuzzy
- Sergeant Major of the Gee
- Posts: 352
- Joined: Sun Oct 09, 2005 4:16 pm
- Location: Omaha, NE
chain vs gear driven block
Can I use a 641087 block to build a chain-driven engine? Are there any modifications that need to be done, or can the 638632 block and 641087 block be used interchangeably for a chain-driven setup?
1942 Ford GPW 74448
1951 M100 01174749
1951 M100 01174749
- Sean Collins
- G-Colonel
- Posts: 1422
- Joined: Fri Mar 19, 2004 7:40 am
- Location: North Idaho
- Contact:
Re: chain vs gear driven block
Yes.Fuzzy wrote:Can I use a 641087 block to build a chain-driven engine?
No, but you have to use chain-drive components: camshaft, oil pump, timing cover, and of course timing chain & sprockets.Are there any modifications that need to be done
Yes, as above.or can the 638632 block and 641087 block be used interchangeably for a chain-driven setup?
638632 "CC" blocks are gear drive, 638632 w/no "CC" are chain drive.
- Fuzzy
- Sergeant Major of the Gee
- Posts: 352
- Joined: Sun Oct 09, 2005 4:16 pm
- Location: Omaha, NE
-
- G-Lieutenant General
- Posts: 6878
- Joined: Sat Jan 12, 2008 5:25 am
- Location: Tipton,In.
Re: chain vs gear driven block
So the 641087 block is a gear drive block ??
Would you need to block the gear oiler nozzle port when converting to chain ??
Would you need to block the gear oiler nozzle port when converting to chain ??
Mike Wolford
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
-
- G-Colonel
- Posts: 1684
- Joined: Thu Mar 13, 2003 4:45 pm
- Location: Northeast Colorado
Re: chain vs gear driven block
I wouldn't think so, unless it's actually in the path of the chain. It could still be used to lube the chain & sprockets, and I think it would do a better job than the hole thru the crank and sprocket that the chain-drive engines used. BWWolfman wrote:So the 641087 block is a gear drive block ??
Would you need to block the gear oiler nozzle port when converting to chain ??
G Trp 2nd Sqdrn 3d Armored Cavalry Ft. Lewis 1970-71. 43GPW(Sarge?) 47CJ2A(Teddy) 47CJ2A(Rusty) 47CJ2A(Zak) 48CJ2A(Lefty) 48CJ2A(Uncle Linden) 53CJ3B(Bulldog) 88XJ(Pluto) NE CO
-
- G-Lieutenant General
- Posts: 6878
- Joined: Sat Jan 12, 2008 5:25 am
- Location: Tipton,In.
Re: chain vs gear driven block
The chain track would be the most concern. No doubt the oiler nozzle would do a better job of lubrication.
I'm thinking.
The cam and crankshaft are centered in the same location for both chain and gear drive.
With the gear drive, the crank gear and cam gear are a larger diameter than the crank sprocket and cam sprocket on a chain drive installation so the gears mesh together. The oil nozzle is positioned above the crank gear.
The crank sprocket and cam chain sprocket are smaller in diameter than the gear drive gears so the chain track would be closer to the center line of the crank and cam and closer to the oil nozzle position.
??????????
Just thinking on line.
Some times I think too much.
Guess it is all irrelevant. If the nozzle was in the way of the chain, it would become obvious pretty quick.
Be nice !
I'm thinking.
The cam and crankshaft are centered in the same location for both chain and gear drive.
With the gear drive, the crank gear and cam gear are a larger diameter than the crank sprocket and cam sprocket on a chain drive installation so the gears mesh together. The oil nozzle is positioned above the crank gear.
The crank sprocket and cam chain sprocket are smaller in diameter than the gear drive gears so the chain track would be closer to the center line of the crank and cam and closer to the oil nozzle position.
??????????
Just thinking on line.
Some times I think too much.
Guess it is all irrelevant. If the nozzle was in the way of the chain, it would become obvious pretty quick.
Be nice !
Mike Wolford
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
-
- G-Colonel
- Posts: 1684
- Joined: Thu Mar 13, 2003 4:45 pm
- Location: Northeast Colorado
Re: chain vs gear driven block
Me too Mike, just thinking. I don't think I would use both oiling methods, if the nozzle works, I'd block the passage in the crank. BW
G Trp 2nd Sqdrn 3d Armored Cavalry Ft. Lewis 1970-71. 43GPW(Sarge?) 47CJ2A(Teddy) 47CJ2A(Rusty) 47CJ2A(Zak) 48CJ2A(Lefty) 48CJ2A(Uncle Linden) 53CJ3B(Bulldog) 88XJ(Pluto) NE CO
-
- G-Sergeant First Class
- Posts: 90
- Joined: Thu Jun 02, 2011 4:47 am
- Location: Arvada, Colorado
-
- G-Lieutenant General
- Posts: 6878
- Joined: Sat Jan 12, 2008 5:25 am
- Location: Tipton,In.
Re: chain vs gear driven block
I think the photos just answered this question.
Even if a new chain missed the oiler nozzle, the oiler is on the slack side for a chain drive set up and it would not be long before wear and chain slack would take the nozzle off the front of the block. Big oil leak and who knows where the nozzle might end up.
Block the oiler passage.
Don't think the gear drive crank is drilled. I always wondered how much good the passage did anyway ?? All the oil being returned on top of the timing cover should be sufficient. Unless there was not a filter and return line ??
I think the oil filter was an after thought and the passage was pre filter.
Even if a new chain missed the oiler nozzle, the oiler is on the slack side for a chain drive set up and it would not be long before wear and chain slack would take the nozzle off the front of the block. Big oil leak and who knows where the nozzle might end up.
Block the oiler passage.
Don't think the gear drive crank is drilled. I always wondered how much good the passage did anyway ?? All the oil being returned on top of the timing cover should be sufficient. Unless there was not a filter and return line ??
I think the oil filter was an after thought and the passage was pre filter.
Mike Wolford
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: chain vs gear driven block
Even if the change could be done, there is a concern about an oil pressure drop at the front of the block.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
-
- G-Lieutenant General
- Posts: 6878
- Joined: Sat Jan 12, 2008 5:25 am
- Location: Tipton,In.
Re: chain vs gear driven block
I am a little slow sometimes but. Guess that fits in with the rest of the responders.
This going to be a non issue.
There is a difference in the height of the engine front plate.
The gear drive plate is taller than the chain drive plate.
With the chain drive, you will have to use the cover with the pin to hold the cam in place so you will have to use a chain drive front plate.
The chain drive front plate does not have a cut out above the crank for the oil nozzle so you won't be able to install a nozzle.
You will need to install a flat plug in the nozzle oiler hole so you can use the chain drive front plate.
Be sure to install an oil filter. The return is the only lube oil the chain will get since the gear crank is not drilled.
That was a long time coming !
Curious ? Why are you installing a chain drive in a geared engine ??
This going to be a non issue.
There is a difference in the height of the engine front plate.
The gear drive plate is taller than the chain drive plate.
With the chain drive, you will have to use the cover with the pin to hold the cam in place so you will have to use a chain drive front plate.
The chain drive front plate does not have a cut out above the crank for the oil nozzle so you won't be able to install a nozzle.
You will need to install a flat plug in the nozzle oiler hole so you can use the chain drive front plate.
Be sure to install an oil filter. The return is the only lube oil the chain will get since the gear crank is not drilled.
That was a long time coming !
Curious ? Why are you installing a chain drive in a geared engine ??
Mike Wolford
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
- Fuzzy
- Sergeant Major of the Gee
- Posts: 352
- Joined: Sun Oct 09, 2005 4:16 pm
- Location: Omaha, NE
Re: chain vs gear driven block
I'm trying to get my MB engine rebuilt, but the shop found big cracks so they suggested a new block would be cheaper and better than a repair. Unfortunately wartime blocks in good shape ready for rebuild are not easy to come by, so I'm trying to see if a CJ block would work.
1942 Ford GPW 74448
1951 M100 01174749
1951 M100 01174749
-
- G-Lieutenant General
- Posts: 6878
- Joined: Sat Jan 12, 2008 5:25 am
- Location: Tipton,In.
Re: chain vs gear driven block
Got it.
If you go up to Athawks pictures, you will see what I am talking about.
One of his pictures shows a gear drive front plate on a chain drive block.
You can clearly see the hole in the front plate for the cam retaining plate is taller than the block behind it. There is an uncovered hole at the top of the cam retaining plate hole in the front engine plate..
Going the opposite way as you are after, a chain front plate on a gear drive block will work because the round hole for the cam brass thrust washer will not leave that hole uncovered. The chain drive components on the gear drive block will work.
I have done this.
If you go up to Athawks pictures, you will see what I am talking about.
One of his pictures shows a gear drive front plate on a chain drive block.
You can clearly see the hole in the front plate for the cam retaining plate is taller than the block behind it. There is an uncovered hole at the top of the cam retaining plate hole in the front engine plate..
Going the opposite way as you are after, a chain front plate on a gear drive block will work because the round hole for the cam brass thrust washer will not leave that hole uncovered. The chain drive components on the gear drive block will work.
I have done this.
Mike Wolford
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
CJ-2A
VEP GPW
Comm./Inst. SEL
AOPA ( 50 yrs)
EAA ( 49 yrs)
4th Inf. Div. - 5th Inf. Div. - 2nd Armor Div. - CIB
- Sean Collins
- G-Colonel
- Posts: 1422
- Joined: Fri Mar 19, 2004 7:40 am
- Location: North Idaho
- Contact:
Re: chain vs gear driven block
No there isn't. They are both the same outer dimensions.Wolfman wrote: There is a difference in the height of the engine front plate.
The gear drive plate is taller than the chain drive plate.
Not so. EITHER front plate will work.... so you will have to use a chain drive front plate.
ALL crankshafts made up thru mid-Jan '48 were drilled for chain lubrication. As long as it has the annular groove on the nose shaft, it's good for chain timing.Be sure to install an oil filter. The return is the only lube oil the chain will get since the gear crank is not drilled
- Sean Collins
- G-Colonel
- Posts: 1422
- Joined: Fri Mar 19, 2004 7:40 am
- Location: North Idaho
- Contact:
Re: chain vs gear driven block
Don't get sidetracked by the conjecturing. Your MB engine guts will fit right into a gear drive block w/out modifications.Fuzzy wrote:I'm trying to get my MB engine rebuilt, but the shop found big cracks so they suggested a new block would be cheaper and better than a repair. Unfortunately wartime blocks in good shape ready for rebuild are not easy to come by, so I'm trying to see if a CJ block would work.
Remove the gear squirt nozzle (if present) and plug the hole. The chain will receive its NORMAL FACTORY lubrication via the crankshaft drillings.
Who is online
Users browsing this forum: No registered users and 39 guests