Side Panel Piece Needed MBT
-
- Sergeant Major of the Gee
- Posts: 436
- Joined: Fri Feb 17, 2017 4:40 pm
- Location: Illinois And New Mexico
Side Panel Piece Needed MBT
Hi everyone:
I'm looking for a piece of the side panel from an MBT with the indent in it. If you look at the photo mine was cut to accommodate the exhaust pipe from a generator that was mounted in the trailer. The hole size is about 2", so all I would need is a piece around 4" x 4" that includes the indent. Obviously I'm willing to pay for the piece plus shipping so please let me know if there are any donors out there.
I'm looking for a piece of the side panel from an MBT with the indent in it. If you look at the photo mine was cut to accommodate the exhaust pipe from a generator that was mounted in the trailer. The hole size is about 2", so all I would need is a piece around 4" x 4" that includes the indent. Obviously I'm willing to pay for the piece plus shipping so please let me know if there are any donors out there.
- Attachments
-
- IMG_3596.JPG (203.75 KiB) Viewed 1132 times
Adam Smith
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
- Eddie Holland
- G-Colonel
- Posts: 1582
- Joined: Sat Nov 29, 2003 4:22 am
- Location: Calvert City Kentucky
Re: Side Panel Piece Needed MBT
seriously.. square that hole up.... then bend a piece of poster board to that shape and trace it. Then cut the part out of metal and bend it.. weld it in and grind the welds and you will never know it was replaced.
42 GPW 12/30/42 Matching #'s 88,638 being restored
Restoring
M-151 Ford
M-151-A1 Ford
M-151-A2 AMG restored
2 M-416 restored
restoring 2 M-100s
Restoring
M-151 Ford
M-151-A1 Ford
M-151-A2 AMG restored
2 M-416 restored
restoring 2 M-100s
-
- Sergeant Major of the Gee
- Posts: 436
- Joined: Fri Feb 17, 2017 4:40 pm
- Location: Illinois And New Mexico
Re: Side Panel Piece Needed MBT
Thanks Eddie. I'm sure I could make it using the method you mentioned, just thought if anyone had a scrap piece it would make it easier on me. Totally new to this so appreciate the advice.
Adam Smith
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
- Eddie Holland
- G-Colonel
- Posts: 1582
- Joined: Sat Nov 29, 2003 4:22 am
- Location: Calvert City Kentucky
Re: Side Panel Piece Needed MBT
i think you could show it to a welder and get it fixed pretty easy.
42 GPW 12/30/42 Matching #'s 88,638 being restored
Restoring
M-151 Ford
M-151-A1 Ford
M-151-A2 AMG restored
2 M-416 restored
restoring 2 M-100s
Restoring
M-151 Ford
M-151-A1 Ford
M-151-A2 AMG restored
2 M-416 restored
restoring 2 M-100s
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: Side Panel Piece Needed MBT
Honestly, Eddie’s method is the simplest and easiest. Harbor Freight tools sells an 18” bender perfect for this and it’s about $40. Home Depot will probably have small squares of 18 gauge metal.
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
-
- Sergeant Major of the Gee
- Posts: 436
- Joined: Fri Feb 17, 2017 4:40 pm
- Location: Illinois And New Mexico
Re: Side Panel Piece Needed MBT
Thanks guys. I'm driving into town tomorrow so will check out the bender at Harbor Freight. Probably going to need one for the GPW anyway.
Adam Smith
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
-
- G-Sergeant
- Posts: 33
- Joined: Mon Sep 21, 2015 6:16 pm
- Location:
Re: Side Panel Piece Needed MBT
I just picked up 2 pieces of 18"x6"x16ga steel for $7.32 each at Home Depot. Ken
-
- G-Second Lieutenant
- Posts: 575
- Joined: Thu Dec 27, 2012 5:37 pm
- Location: Kissimmee FL
Re: Side Panel Piece Needed MBT
Hi all
Rotted out or flutes needing repair ????
Anyone can make these cheaply without having to buy a complete front/back or side panel !!!!
couple strips of 1/4 thick by 1 inch strip and you can easy make them yourself
here`s a little former I made that took no more than 20 minutes
spend a bit longer an you`ll have an even better one
two pieces of 1/4 thick X 1 inch bar grind a 45 degree on one side of each bar.
with a short length do the same and round off the end.
make a cross piece that will be the top former and make a curve with the 45 degree angle
if you want to make the lower flute on either the front or rear panel then make two and cut the long bars to the correct length.
make up a former and with a BFH if you don`t have a HF press beat crap out of it just like I did
I`d post the pics but seems my phone takes to large an image !!!!
Geoff Bull
Rotted out or flutes needing repair ????
Anyone can make these cheaply without having to buy a complete front/back or side panel !!!!
couple strips of 1/4 thick by 1 inch strip and you can easy make them yourself
here`s a little former I made that took no more than 20 minutes
spend a bit longer an you`ll have an even better one
two pieces of 1/4 thick X 1 inch bar grind a 45 degree on one side of each bar.
with a short length do the same and round off the end.
make a cross piece that will be the top former and make a curve with the 45 degree angle
if you want to make the lower flute on either the front or rear panel then make two and cut the long bars to the correct length.
make up a former and with a BFH if you don`t have a HF press beat crap out of it just like I did
I`d post the pics but seems my phone takes to large an image !!!!
Geoff Bull
- Eddie Holland
- G-Colonel
- Posts: 1582
- Joined: Sat Nov 29, 2003 4:22 am
- Location: Calvert City Kentucky
Re: Side Panel Piece Needed MBT
i wish you could post pictures.. Sounds interesting but ya lost me..
42 GPW 12/30/42 Matching #'s 88,638 being restored
Restoring
M-151 Ford
M-151-A1 Ford
M-151-A2 AMG restored
2 M-416 restored
restoring 2 M-100s
Restoring
M-151 Ford
M-151-A1 Ford
M-151-A2 AMG restored
2 M-416 restored
restoring 2 M-100s
- lt.luke
- G-General
- Posts: 9899
- Joined: Fri May 09, 2003 7:56 am
- Location: Oklahoma
- Contact:
Re: Side Panel Piece Needed MBT
That terribly bubba’d Trailer of mine is back in my control. If you’re patient, I’ll get you a piece to patch.
Luke Sparks
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
MAJ (R), USA
GPW 12078 http://g503.com/forums/viewtopic.php?f=95&t=102532
https://www.homesteadersfinest.com/
-
- Sergeant Major of the Gee
- Posts: 436
- Joined: Fri Feb 17, 2017 4:40 pm
- Location: Illinois And New Mexico
Re: Side Panel Piece Needed MBT
Thanks Luke, much appreciated!
Adam Smith
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
GPW 80535, 11-19-42
MBT 2470, 8-42, USA #0160905
Who is online
Users browsing this forum: No registered users and 50 guests