Bantam wiring clip location?
-
- Sergeant Major of the Gee
- Posts: 474
- Joined: Sun Apr 18, 2004 2:43 pm
- Location: Everett, Wa
Bantam wiring clip location?
Looking for a detailed pic of the clip that holds the vehicle cable to the top of the frame rail, thanks
Willys MB 340931. DOD 6-9-1944
Mvpa 1996 convention 1st place motorpool class
Dodge wc-12, July, 1941
Mvpa 1996 convention 1st place motorpool class
Dodge wc-12, July, 1941
- lowbonnet
- G-Brigadier General
- Posts: 2173
- Joined: Fri Dec 13, 2002 11:56 pm
- Location: Holland
Re: Bantam wiring clip location?
This image shows the clip close to the trailer body on the top of the rail.
June 1942 Ford GPW (script)
Transportation Equipment Co. T1, 1/4 ton trailer
Transportation Equipment Co. T1, 1/4 ton trailer
-
- G-Second Lieutenant
- Posts: 587
- Joined: Fri Jul 16, 2004 4:27 pm
- Location: Lincoln, California
- Contact:
Re: Bantam wiring clip location?
Tony,
Hope these pictures will assist your needs. I believe this is correct.
Ben
Hope these pictures will assist your needs. I believe this is correct.
Ben
http://www.jarheadjeep.com[url]
MB Body # 204065 date 1/19/43
GPW Engine # 12492 date 3/31/42
GPW Frame # 47894 date 7/?/42
Bantam T-3 1943 1/4 trailer USA # 0269414
http://www.jarheadjeep.com/Bens_1943_Ba ... railer[url]
PE 210 Power Unit Radio Generator 3/15/44
MB Body # 204065 date 1/19/43
GPW Engine # 12492 date 3/31/42
GPW Frame # 47894 date 7/?/42
Bantam T-3 1943 1/4 trailer USA # 0269414
http://www.jarheadjeep.com/Bens_1943_Ba ... railer[url]
PE 210 Power Unit Radio Generator 3/15/44
-
- Sergeant Major of the Gee
- Posts: 474
- Joined: Sun Apr 18, 2004 2:43 pm
- Location: Everett, Wa
Re: Bantam wiring clip location?
Perfect thanks!
Willys MB 340931. DOD 6-9-1944
Mvpa 1996 convention 1st place motorpool class
Dodge wc-12, July, 1941
Mvpa 1996 convention 1st place motorpool class
Dodge wc-12, July, 1941
- Chuck Lutz
- Gee Addict
- Posts: 26829
- Joined: Wed Jun 28, 2006 7:00 am
- Location: Jeep Heaven
Re: Bantam wiring clip location?
Tony....interestingly enough, both the drawbars have the same part number...meaning they are interchangeable. So...if yours look to be a little dinged up, you can swap them from side to side to get the "best" top rail part where it can be seen....and of course that means the hole in the top of the drawbar for the clip screw was put into all drawbars in the same place so that no matter which side you installed them on...the hole would be in the correct location.
Here is my set up:
Here is my set up:
Chuck Lutz
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
GPW 17963 4/24/42 Chester, PA. USA 20113473 (USA est./Tom W.)
Bantam T3-C 1947
Who is online
Users browsing this forum: No registered users and 57 guests