Looking for gaskets
-
- G-Staff Sergeant
- Posts: 59
- Joined: Thu Nov 17, 2011 2:25 pm
- Location: Washington State
Looking for gaskets
I'm looking for the head , intake / exhaust gaskets for my PE-95-K power unit ,
what I know about Willys four cylinder engines is about zero , can anyone help
me with part numbers , are the gaskets available through places like Car-quest
or NAPA ? , the reason I ask about auto the auto parts stores is that I have rebuilt
many six cylinder continental F-245 flat heads and always acquired full and partial
gasket sets through Car-quest ... , so where do I start to look for the numbers
that I need to find ? , any input , help or comments much appreciated . Thanks ,
Kris
Found another number on the machined surface of the block
just above the water pump , stamped ; RMC 49293
what I know about Willys four cylinder engines is about zero , can anyone help
me with part numbers , are the gaskets available through places like Car-quest
or NAPA ? , the reason I ask about auto the auto parts stores is that I have rebuilt
many six cylinder continental F-245 flat heads and always acquired full and partial
gasket sets through Car-quest ... , so where do I start to look for the numbers
that I need to find ? , any input , help or comments much appreciated . Thanks ,
Kris
Found another number on the machined surface of the block
just above the water pump , stamped ; RMC 49293
Last edited by krisinwa.st. on Thu May 12, 2016 10:18 am, edited 1 time in total.
- 1943Willysgpw
- G-Major General
- Posts: 2740
- Joined: Wed Sep 11, 2013 9:02 am
- Location: Edmond, OK
Re: Looking for gaskets
FS7267B Felpro. I think that FS7285B will work as well. O'reilly, AutoZone, Car Quest should all have this.
"None of us are as smart as all of us"
1942 GPW 1871 DoD 2-27-42 Dallas Plant
1945 GPW 247890 DoD 1-26-45 Louisville Plant
1942 GTB 136166 DoD 9-18-42
1942 GTB 135938 DoD
1952 M100
1942 GPW 1871 DoD 2-27-42 Dallas Plant
1945 GPW 247890 DoD 1-26-45 Louisville Plant
1942 GTB 136166 DoD 9-18-42
1942 GTB 135938 DoD
1952 M100
-
- G-Staff Sergeant
- Posts: 59
- Joined: Thu Nov 17, 2011 2:25 pm
- Location: Washington State
Re: Looking for gaskets
Thanks for the information , I looked up the two Felpro part numbers , looks like1943Willysgpw wrote:FS7267B Felpro. I think that FS7285B will work as well. O'reilly, AutoZone, Car Quest should all have this.
there is a difference in the head gasket , one is early and one is late , I'm not sure
what motor I have , some numbers that I found ; on the packing list , Engine , Willys
No. 807532 ( in use ) , Stock number NSNR , John R Hollingsworth corp. Clifton Heights
PA. , order # 38203 / Phila 53-51 . also this number/letter combo cast on the right
side of the engine block just above the oil pan ; 641087-L-W-12-A-N1-CR-N2
The two Felpro numbers above are full engine sets , I only need a head , intake exhaust
and side cover gaskets as I only plan to get the valves unstuck , cleaned up and hand
lapped . Any idea what engine ( early or late ) I have , possibly a year ? . Thanks again ,
Kris
Another number , stamped on the machined surface on the front of the block
just above the water pump ; RMC 49293
-
- G-Staff Sergeant
- Posts: 59
- Joined: Thu Nov 17, 2011 2:25 pm
- Location: Washington State
A few pictures of the motor numbers
Power Unit PE-95-K , Willys Engine numbers
Any idea what year this engine is , was the " Industrial " only used in gen sets ?
would it use the late rather than the early head gasket ? is the intake / exhaust
gasket the same for early and late engines ? , Like I said earlier I know close to
zero about Willys motors ... so I ask a lot of questions , Thanks , Kris
Any idea what year this engine is , was the " Industrial " only used in gen sets ?
would it use the late rather than the early head gasket ? is the intake / exhaust
gasket the same for early and late engines ? , Like I said earlier I know close to
zero about Willys motors ... so I ask a lot of questions , Thanks , Kris
- 1943Willysgpw
- G-Major General
- Posts: 2740
- Joined: Wed Sep 11, 2013 9:02 am
- Location: Edmond, OK
Re: Looking for gaskets
That would be the late one. Also, If you were to buy the gaskets individually, it would probably be the same amount. The gasket number is the same for the head, just put HS in front of the number instead. You can look up each individual gasket off of a 1945 Jeep Willys. That is how Oreilly auto parts has it stored. I also have FelPro gasket vintage catalog. I would be happy to email it to you.
"None of us are as smart as all of us"
1942 GPW 1871 DoD 2-27-42 Dallas Plant
1945 GPW 247890 DoD 1-26-45 Louisville Plant
1942 GTB 136166 DoD 9-18-42
1942 GTB 135938 DoD
1952 M100
1942 GPW 1871 DoD 2-27-42 Dallas Plant
1945 GPW 247890 DoD 1-26-45 Louisville Plant
1942 GTB 136166 DoD 9-18-42
1942 GTB 135938 DoD
1952 M100
-
- G-Staff Sergeant
- Posts: 59
- Joined: Thu Nov 17, 2011 2:25 pm
- Location: Washington State
Re: Looking for gaskets
Sounds good , thanks for the help . PM sent1943Willysgpw wrote:That would be the late one. Also, If you were to buy the gaskets individually, it would probably be the same amount. The gasket number is the same for the head, just put HS in front of the number instead. You can look up each individual gasket off of a 1945 Jeep Willys. That is how Oreilly auto parts has it stored. I also have FelPro gasket vintage catalog. I would be happy to email it to you.
-
- G-Lieutenant General
- Posts: 4528
- Joined: Sun Jul 20, 2003 6:03 pm
- Location: Little Meadows PA
Re: Looking for gaskets
That head didnt come with that engine. RMC=rebuilt military model c. block is from a m38 jeep 1952 ish
Adam
Adam
-
- G-Staff Sergeant
- Posts: 59
- Joined: Thu Nov 17, 2011 2:25 pm
- Location: Washington State
Re: Looking for gaskets
Adam wrote:That head didnt come with that engine. RMC=rebuilt military model c. block is from a m38 jeep 1952 ish
Adam
Thanks Adam , so the block is for the M38 jeep , do you know what the head was
originally fitted to ? , I have removed the head and see where a Victor head gasket
# 1022 was used , so I figure that is the correct gasket , I've tried to cross reference
it to FelPro with no luck , is FelPro 7825 B the correct gasket to use for this motor/
head combo. ? , Kris
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Looking for gaskets
Please post a pic of the firing chamber configuration and I will pick you the correct Fel-Pro replacement head gasket.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
-
- G-Staff Sergeant
- Posts: 59
- Joined: Thu Nov 17, 2011 2:25 pm
- Location: Washington State
Re: Looking for gaskets
A few pictures , thanks Ben ,
-
- G-Lieutenant General
- Posts: 4528
- Joined: Sun Jul 20, 2003 6:03 pm
- Location: Little Meadows PA
Re: Looking for gaskets
The b looks like it. Big oval water hole in middle. Go to ebay and search willys mb head gasket. You will see yours and the earlier one. The head probably came off a welder or pump or something. I dont know the diff betwen the original head and this one.
Adam
Adam
-
- G-Staff Sergeant
- Posts: 59
- Joined: Thu Nov 17, 2011 2:25 pm
- Location: Washington State
Re: Looking for gaskets
Adam wrote:The b looks like it. Big oval water hole in middle. Go to ebay and search willys mb head gasket. You will see yours and the earlier one. The head probably came off a welder or pump or something. I dont know the diff betwen the original head and this one.
Adam
Thanks Adam , will do
-
- Jeep Heaven
- Posts: 49841
- Joined: Sun Mar 02, 2008 12:37 pm
- Location: Proving Ground
Re: Looking for gaskets
Sorry, I did not get to my heads and gaskets. Will try Monday. I disagree with Adam, many PE-95's were re-engined in late 50's with new engines that had the industrial cylinder heads. You will note your engine has rotating valves also.
2011 MVPA PIONEER AWARD - MVPA #1064
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
HONOR GRAD-WHEELED VEHICLE MECHANIC SCHOOL 1960 - US ARMY ORDNANCE SCHOOL(MACHINIST) ABERDEEN PG 1962 - O-1 BIRD DOG CREWCHIEF - 300,000+TROUBLE FREE M-38A1 MILES
LIFE MEMBER AM LEGION-40/8-DAV
7 MIL SPEC MAINTAINED MV'S
COL. BRUNO BROOKS (ARMY MOTORS) IS MY HERO
-
- G-Brigadier General
- Posts: 2099
- Joined: Sun Jun 03, 2007 9:25 pm
- Location: Nevada
Re: Looking for gaskets
I bought half of the remaining gaskets for my units a while ago.
Restoring June '42 Script GPW Phone 443-865-4800 / Email davidmorganthall@gmail.com
Who is online
Users browsing this forum: No registered users and 4 guests