Ok Im right behind Mike on my restoration ( which by the way is very motivating and looks Awesome) I need a few small parts to get it going. Ive decided not to start it until I get it almost all together. Here are the parts I need,
1 electric exhaust governor rod to carburetor plus clips
2 Electric heat cutoff switch ( mine broke right at the wire mount)
3 Rubber fuel line or at least the ends to compare for building a new one
4 fuel bowl / strainer under gas tank
5 start relay that mounts on back of dash.
6 fuel line pump to carb
7 oil drain pipe support clamp
8 top battery support bracket
These should put me at 95% done. Also any dimensions on the wood battery support blocks. I burned mine thinking they were bubba add on stuff
thanks Matt
PE 95 G also almost done/ Final needs.
- matt506
- G-Major
- Posts: 836
- Joined: Thu Feb 27, 2003 11:00 pm
- Location: Fredonia, Wi
- Contact:
PE 95 G also almost done/ Final needs.
SFC Matt Miller,
4-42 GPW,
M-6 81mm hand cart,
4-43 MBT,
4-43 WLA,
1961 M151,
M18 paracaisson,
"Find The Bastards and Pile On" 11th ACR
4-42 GPW,
M-6 81mm hand cart,
4-43 MBT,
4-43 WLA,
1961 M151,
M18 paracaisson,
"Find The Bastards and Pile On" 11th ACR
-
- G-Sergeant
- Posts: 49
- Joined: Sun Nov 23, 2014 4:07 am
- Location: Jamison PA
Re: PE 95 G also almost done/ Final needs.
Hi Matt,
Reading through your list, may I make a suggestion on a few of them?
The choke rod can be fabbed up from round stock in that size. It's not a complicated piece if you can't get a used one. Clips are a NAPA item.
I'm not sure where the rubber line would be. I plumbed all steel line for mine, no rubber at all. Go to NAPA and get a 20" piece of pre flared 3/8" brake line for the pump to carb. Get a bender and fab it up to fit. I used that for mine, as it has the correct bead flared ends for high pressure. Fits perfectly.
Pump to tank was a long brake line 1/4" for that one. Again bend as necessary and has correct beaded flare for high pressure.
Fuel bowl can be one from Tractor Supply. Looks the same as far as I see
I didn't go with two 6V batteries for cost reasons. I am making my own hold down and wood bottom to fit. I may change my mind for originality, but the battery I have cost me nothing right now.
Reading through your list, may I make a suggestion on a few of them?
The choke rod can be fabbed up from round stock in that size. It's not a complicated piece if you can't get a used one. Clips are a NAPA item.
I'm not sure where the rubber line would be. I plumbed all steel line for mine, no rubber at all. Go to NAPA and get a 20" piece of pre flared 3/8" brake line for the pump to carb. Get a bender and fab it up to fit. I used that for mine, as it has the correct bead flared ends for high pressure. Fits perfectly.
Pump to tank was a long brake line 1/4" for that one. Again bend as necessary and has correct beaded flare for high pressure.
Fuel bowl can be one from Tractor Supply. Looks the same as far as I see
I didn't go with two 6V batteries for cost reasons. I am making my own hold down and wood bottom to fit. I may change my mind for originality, but the battery I have cost me nothing right now.
MIke
1944 Hobart PE-197
1945 Onan PU/8
1945 PE-95G
1944 Hobart PE-197
1945 Onan PU/8
1945 PE-95G
- matt506
- G-Major
- Posts: 836
- Joined: Thu Feb 27, 2003 11:00 pm
- Location: Fredonia, Wi
- Contact:
Re: PE 95 G also almost done/ Final needs.
Mike,
You are correct I just thought maybe if a few of these parts were out there.....
Would you happen to know the length and dia for the rod? Ill get the clips tonight. I do have the rubber line in bulk but i just need to know what ends to crimp on, otherwise im going your route with steel. Thanks a ton. Matt
You are correct I just thought maybe if a few of these parts were out there.....
Would you happen to know the length and dia for the rod? Ill get the clips tonight. I do have the rubber line in bulk but i just need to know what ends to crimp on, otherwise im going your route with steel. Thanks a ton. Matt
SFC Matt Miller,
4-42 GPW,
M-6 81mm hand cart,
4-43 MBT,
4-43 WLA,
1961 M151,
M18 paracaisson,
"Find The Bastards and Pile On" 11th ACR
4-42 GPW,
M-6 81mm hand cart,
4-43 MBT,
4-43 WLA,
1961 M151,
M18 paracaisson,
"Find The Bastards and Pile On" 11th ACR
-
- G-Brigadier General
- Posts: 2010
- Joined: Thu Jul 10, 2003 4:13 pm
- Location:
Re: PE 95 G also almost done/ Final needs.
Hi Matt, Sent u an email. Best wishes; Leo
Who is online
Users browsing this forum: No registered users and 2 guests