G503.com Message Forums
Military Vehicles, WWII Jeeps and more!
Oil Pressure Sending Unit Nipple Length?
Moderator: Moderator
6 posts
• Page 1 of 1
Oil Pressure Sending Unit Nipple Length?
by dfield » Mon May 24, 2010 1:02 pm
What is the length of the oil pressure sending unit nipple that comes out of the side of the block?
Looking for the following parts to finish my 1952 M38: fuel tank straps, front seat pans, battery cables, top bow rods, patch body panels for rear corners. NOS 0-60 psi oil pressure sending unit with Douglas connector. NOS head light dimmer switch.
-
dfield - G-Lieutenant Colonel
- Posts: 1153
- Joined: Tue Apr 19, 2005 6:41 pm
- Location: Orange County California
Re: Oil Pressure Sending Unit Nipple Length?
by Cuz » Mon May 24, 2010 5:14 pm
1 inch
Cuz (AKA Wes K)
45 MB, 51 M38, 54 M37, 6? M101A1, 60 CJ5, 76 DJ5D & 47 T3-C
45 MB, 51 M38, 54 M37, 6? M101A1, 60 CJ5, 76 DJ5D & 47 T3-C
- Cuz
- G-Lieutenant General
- Posts: 6622
- Joined: Fri Feb 23, 2007 12:26 pm
- Location: Northwestern Wisconsin
Re: Oil Pressure Sending Unit Nipple Length?
by dfield » Mon May 24, 2010 8:22 pm
Thanks Wes. Ace had a 3/4" and 1 1/2" but no 1". They also had 3" so I bought one of those and will cut and thread it.
Looking for the following parts to finish my 1952 M38: fuel tank straps, front seat pans, battery cables, top bow rods, patch body panels for rear corners. NOS 0-60 psi oil pressure sending unit with Douglas connector. NOS head light dimmer switch.
-
dfield - G-Lieutenant Colonel
- Posts: 1153
- Joined: Tue Apr 19, 2005 6:41 pm
- Location: Orange County California
Re: Oil Pressure Sending Unit Nipple Length?
by Ben Dover » Mon May 24, 2010 8:38 pm
It is not a nipple, It is a 1/4" X 1/8" Black Iron Street Elbow. I believe you will find it described in the SNL. If not just go to a plumbing supply store that has iron pipe fittings. 1/4" Female X 1/8" male to be exact.
(the Army taught me how to ID pipe fittings 50 years ago
)
(the Army taught me how to ID pipe fittings 50 years ago
)PROUD 2011 MVPA PIONEER AWARDEE-HONOR GRAD WHEELED VEHICLE MECHANIC SCHOOL 1960- US ARMY ORDNANCE SCHOOL(MACHINIST) APG 1962 - O-1 BIRD DOG CREWCHIEF - 68 NONSTOP BY THE BOOK ARMY TRUCK-JEEP YEARS LIFETIME AM LEGION DAV 40/8- MVPA 1064 -7 TURNKEY MV'S
- Ben Dover
- Gee Addict
- Posts: 22654
- Joined: Sun Mar 02, 2008 2:37 pm
- Location: Proving Ground
Re: Oil Pressure Sending Unit Nipple Length?
by Cuz » Tue May 25, 2010 8:31 pm
It is a nipple and it is installed in the block and a 90 deg female 1/8"P to female 1/4"P reducer is then installed 0n the nipple.
This is what the ORD 9 SNL G-740 really says!
This is what the ORD 9 SNL G-740 really says!
- senders.JPG (80.39 KiB) Viewed 275 times
- Oil Press sender.JPG (145.25 KiB) Viewed 259 times
Last edited by Cuz on Tue May 25, 2010 11:25 pm, edited 2 times in total.
Cuz (AKA Wes K)
45 MB, 51 M38, 54 M37, 6? M101A1, 60 CJ5, 76 DJ5D & 47 T3-C
45 MB, 51 M38, 54 M37, 6? M101A1, 60 CJ5, 76 DJ5D & 47 T3-C
- Cuz
- G-Lieutenant General
- Posts: 6622
- Joined: Fri Feb 23, 2007 12:26 pm
- Location: Northwestern Wisconsin
Re: Oil Pressure Sending Unit Nipple Length?
by Ben Dover » Tue May 25, 2010 8:34 pm
I'll be darned, and you can pick it up at the same place as the reducing elbow
1/8" Hex Nipple with a place for a wrench in the center..
1/8" Hex Nipple with a place for a wrench in the center..
PROUD 2011 MVPA PIONEER AWARDEE-HONOR GRAD WHEELED VEHICLE MECHANIC SCHOOL 1960- US ARMY ORDNANCE SCHOOL(MACHINIST) APG 1962 - O-1 BIRD DOG CREWCHIEF - 68 NONSTOP BY THE BOOK ARMY TRUCK-JEEP YEARS LIFETIME AM LEGION DAV 40/8- MVPA 1064 -7 TURNKEY MV'S
- Ben Dover
- Gee Addict
- Posts: 22654
- Joined: Sun Mar 02, 2008 2:37 pm
- Location: Proving Ground
6 posts
• Page 1 of 1
Return to M38 Technical Knowledge Base
Who is online
Users browsing this forum: No registered users and 3 guests